CMDFlash Overview

CMDFlash is a flash programmer supporting BDM,EOBD K-LINE,EOBD CAN-BUS,EOBD PWM for all the new generation ECUs.

Key Features:

  • Available in Master/Slave configuration.
  • Automatic checksums.
  • New families / checksums subscription.
  • Recovery function. (You can restart ecu flashing after a programming failure)
  • BDM Motorola/NEXUS MPC
  • Bosch TRICORE BOOT EDC17 MED17 including VAG TP8/TP10
  • C16x / ST10 BOOT
  • CAN V2.0B 1Mb/s
  • K line ISO / KWP
  • J1850 PWM
  • Mitsubishi Lancer EVO 5->9
  • Industrial Vehicles 24V
  • Automatic resistor switch. K-Line 470 ohm pull-up resistor for VAG EDC16
  • Protection dongle is now inside the black box
  • Old cars protocols are now included (EDC15, ME7xx)
  • *NEW* – VAG MED17, EDC17, Simos 12, Simos 18 OBD!

 

The OBD flasher function is available by default on all tools. It is one of the best OBD tools available which supports the very latest ECUs including:

Bosch EDC15 / EDC16 / EDC17

Bosch ME7 / ME9 / MED9 / MED17

Siemens PPD / Simos 6x Simos 10x / MSS6x / MSVxx / MSD8x etc… including some with TP / Various other Siemens controllers.

Numerous others eg. DELPHI , VISTEON, MARELLI, DENSO, SAGEM, TRIONIC etc…

BDM Plugin:

With BDM you need to unplug the ECU from the vehicle, open and connect it to CMDFlash using a connector available on every EDC16,Marelli,Siemens and Delphi ECU. The Software allow you to read/write the Eprom (29bl802 / M58), the internal firmware and the serial e2prom containing the car’s codes. Checksum correction algoritm is automatic for all the ECU families, this means you don’t have to care about checksums calculations.

With this tool it is possible to read all the ecu’s eprom, even after a bad file is programmed, system hang or an interrupted write operation it is always possible to restart the program operation to restore the ECU and start the car. All the ECU data can be stored in a single file with additional info like brand, model, plague, chassis number, data, note, customer ….. with search facilities and information directly integrated in microsoft windows explorer.

TriCore BOOT Plugin:

This new CMDFlash extension allow you to tune IROM and XROM of the new Bosch EDC17 and MED17 ECUs with locked Tricore microprocessor. The product is based on a new additional interface to be connected to the CMDFlash unit. We developed this new interface in order to give to the user the same friendly operative mode as BDM.

For all the EDC17 ECUs with the Bosch pads on the board ( like the old EDC16 BDM ) you just need the new provided EDC17 positioning frame probe, and no more extra-wiring will be required on the front ECU connectors. For some ecus soldering of boot resistors is required.

Just press ID, read or write and the CMDflash interface will do everything automatically, exactly like the old BDM.

We also provide cables for the ECUs like Mercedes EDC17 ( with the pads placed on the other side of the pcb ) you don’t need to extract the pcb from the case.

Power supplied through the CMDFlash interface, no additional table power supply is required.

Don’t use 3rd parts checksums, Full RSA checksum correction for all the cars is included in the plugin.
Many ECUs have IROM or XROM or IROM+XROM configuration. The CMDFlash software automatically read all the ECU contents and saves it for backup in a special folder, in the meantime it extracts only the calibration data area, allowing you to save and tune it, so you don’t have to search calibration data in IROM and/or XROM, CMDFlash will do it for you. The same for the writing.

 

 

 

The CMDFlash Boot Kit includes:

  • CMD Boot interface + flat cable.
  • MPC004 EDC17 positioning frame probe, the probe is compatible with most of the positioning frames present on the market.
  • Mercedes EDC17 cable
  • Universal boot cable
  • CMDFlash Power supply
  • CMDFlash Protected MEDC17 Boot-Mode Plugin
  • RSA checksums for all the ECU

Pricelist Supported Cars List Contact Us

 

Buy Now

Posted in: